The Weatherboard Journal

Villas, bungalows and the timber houses of Auckland

Untreated kiln-dried framing, 1995 to 2005: what changed

20 November 2026

Houses of the 1990s and early 2000s do not usually appear in a journal about villas, but they belong to the same story. For most of the twentieth century, framing was either native heart timber, which carried its own natural durability, or radiata pine that was increasingly given a preservative treatment. Then, for a window of roughly a decade, the rules let builders leave kiln-dried framing untreated. A house consented in those years has a slightly different relationship with moisture and borer than one built before or after.

Treatment before 1995

The Standards New Zealand summary of key historical dates for timber treatment regimes begins in 1952, when wet boric (boron) salt treatments were first introduced. Before that, native timber and some early radiata pine framing went into houses untreated.

The insect behind the concern is household borer, which Scion's fact sheet on household borer says mainly attacks sapwood, with radiata pine sapwood among its common hosts. The same sheet records that infestations were common in houses built with untreated wood and that the universal use of preservative-treated timber has greatly reduced the incidence of the insect.

The 1995 change

According to the same Standards New Zealand timeline, NZS 3602:1995 allowed untreated framing from 11 September 1995, provided that the timber was kiln-dried and that its in-service moisture content did not exceed 18 per cent. The Building Code's compliance document B2/AS1 picked up the change on 28 February 1998. Anything built with untreated kiln-dried framing before that date had to be consented as an Alternative Solution, which is a more individual route through the council.

BRANZ Bulletin 431 (September 2002) describes what the standard required. The framing had to be planer-gauged and kiln-dried at 74 degrees Celsius or above, and it had to be protected from the weather, kept in a dry environment and shielded from ground moisture. The 18 per cent figure was the heart of the matter: according to BRANZ, as long as it is not exceeded during the life of the structure, the timber will not decay, and the moisture level also lowers the risk of borer attack.

Why kiln drying was trusted

The bulletin also records an argument that high-temperature drying does more than remove water. BRANZ says there is evidence that the risk of borer attack is further reduced by kiln drying, particularly where temperatures go above 100 degrees Celsius, because the timber is sterilised and also undergoes changes thought to make it unpalatable to borer, which have trouble digesting very dry wood. Consumer NZ puts the same idea more plainly: kiln drying radiata pine improves borer resistance, provided it stays dry.

That qualifier, provided it stays dry, is where the caution sits. The same bulletin warns that untreated kiln-dried timber should never be used unless there is a guarantee it will remain dry throughout its in-service life. Scion's household borer sheet is similarly cautious: kiln-dried wood may resist attack for a few years, but it is not an adequate substitute for preservative-treated timber.

The reversal, 2003 to 2005

The tide turned in the early 2000s. The Standards New Zealand timeline records that on 9 March 2003 the Building Industry Authority issued Directive 23, requiring treated timber for building consents issued from 1 April 2004, and that treated framing became the requirement for new consents from that date. Consents that already allowed untreated timber stayed valid only if the buildings were completed by 1 April 2005.

The dates matter more than they might seem, because the rule attached to the consent, not to the year the house was finished. A house with a consent from 1996 and one completed in early 2005 might both sit inside the untreated window, while a house consented after April 2004 should not.

The line was refined again in April 2011, when Amendment 7 to B2/AS1 allowed H1.2 boron-treated radiata pine and Douglas fir framing in closed spaces. BRANZ Bulletin 575 summarises the position that followed. Untreated non-durable timber below 18 per cent moisture and protected from wetting is not particularly susceptible to borer or decay, but it is not permitted as framing, with a limited exception for Douglas fir in low-risk buildings. It also notes that boron treatment, now the standard framing treatment, suits internal use where moisture content stays below 20 per cent.

What this means for a house of that age

Nothing in these documents says a house from the untreated window has a problem. The standard was written on the assumption that the framing would stay dry, and many such houses have done exactly that. What the history gives an owner is a set of questions.

An owner who wants to know the facts, rather than the likelihoods, has the option of a specialist borer and moisture assessment. A report on untreated framing from 1995 to 2005 explains what an inspector looks for in houses of this vintage, including moisture readings in the lower framing. The sensible time for it is before a purchase or before building work opens up a wall.

Keeping the framing dry

For houses that do have untreated framing, the maintenance job is mostly the ordinary one: sound cladding and flashings, roof and gutter upkeep, a ventilated subfloor and sensible drainage. BRANZ's 2002 bulletin makes clear that the performance of untreated kiln-dried timber rests on dryness being maintained for the life of the building, which is a longer commitment than it sounds.

If an inspection does find borer or rot in framing, it is worth asking what caused the moisture before deciding on remedies, because treatment that does not address the water tends to be short-lived. A specialist such as Lignum Timber Inspections can report on the timber and its moisture content together, so that any repair or treatment is aimed at the right thing.

Sources

Also in the journal