The Weatherboard Journal

Villas, bungalows and the timber houses of Auckland

Lockwood houses: their history and how to look after one

20 November 2026

Among Auckland's villas and bungalows, a Lockwood house is the odd one out, and it is not hard to spot. The walls are solid timber planks rather than a frame with boards nailed over it, and the corners are finished with aluminium profiles. The system is more than seventy years old now, which makes the oldest examples as much a period house as a 1920s bungalow, with their own habits and maintenance needs.

Where Lockwood came from

Te Ara's account of the building industry says the company was established in Rotorua after two Dutch immigrants, the structural engineer Jo La Grouw and the marketer Johannes (Jan) van Loghem, arrived in New Zealand in 1951. They saw an opportunity to sell kit-set houses made from exotic timber grown in central North Island plantations. By the early 2000s, Te Ara reports, more than 22,000 homes had been built in many designs, and the firm had also built commercial buildings, including Rotorua's Agrodome.

The company's own history adds some detail. The first Lockwood homes were built in 1954, and the very first sold was a fishing bach on the Waiteti Stream at Ngongotaha, built for a doctor from Auckland; the company says it still stands on its original site. The figure of more than 50,000 homes and buildings worldwide is the company's own claim, and it is considerably higher than the 22,000 Te Ara gave for the early 2000s, which is unsurprising given the years in between.

Lockwood belongs to a broader post-war movement towards factory-made houses. Te Ara notes that after the Second World War, companies were set up to mass-produce prefabricated houses, and that Keith Hay built his first transportable house in 1949, during a housing shortage. Kit-set timber houses suited the same mood: quick to put up and made from timber that was available locally.

How the system works

According to the company, Lockwood walls are built from tongue-and-groove radiata pine boards locked together with a patented aluminium X-profile. Joinery sits in custom-built subframes, and tie rods running through the walls give lateral bracing. The exterior board is described as a tight sandwich of solid timber, insulation and cladding.

One consequence follows for an owner. The timber is part of the structure rather than an inner layer behind a separate cladding, so changes in its moisture content matter, and that is why most of the manufacturer's advice below is about keeping moisture out and letting steam escape.

What the manufacturer advises

The company's general maintenance guidance, which is the main published source of Lockwood-specific advice, runs along these lines:

Because this is the manufacturer's own advice, it is sensible to treat it as the starting point. The company also publishes a separate maintenance guide for homes built before 1990, which is the one to ask for if yours dates from the early decades.

Painting and colour

Colour is where owners of older Lockwoods have most choice, and the company's painting page says that if the house has cedar or pine cladding it will need regular painting or staining, while aluminium cladding may need painting if it has not been washed regularly. It also recommends paint or stain colours with a light reflective value of 28 per cent or higher, because dark colours on timber exterior surfaces can cause excessive heat absorption and undesirable timber movement.

That fits the general advice from BRANZ on timber weatherboards. BRANZ says that timber is hygroscopic, so boards move with changes in moisture content, and lists fading and chalking, especially with dark colours, among the appearance problems of timber cladding. Owners planning a repaint can find more on painting a Lockwood home, and should check any scheme against the manufacturer's light-reflectance guidance first.

Checking an older Lockwood

A routine look at an older Lockwood does not take long.

  1. Walk the outside for gaps, dents or punctures in the aluminium sheathing, and for open joints around joinery.
  2. Check the shaded walls for mould, and the base of the walls for damp or splashing.
  3. Look underneath, if the house is on piles, for clear vents and for the tie rods mentioned above.
  4. Look at the interior for condensation, particularly near bathrooms, the kitchen and the laundry, where the manufacturer says steam needs to be able to escape. The company says extractor fans should be properly vented to the outside.
  5. Keep the paperwork. Original plans and any alterations help a later owner or tradesperson understand what they are dealing with.

For anyone planning a repaint or a refresh, Eggshell & Co is one Auckland painting firm with a page on the subject, and it is worth asking any painter how they will treat the aluminium profiles and the joints between boards before work starts.

Sources

Also in the journal